Installation and commissioning Baker Hughes LM9000 Aeroderivative Gas Turbine and Compressors. Check wiring of components (transmitters, valves, motors, pumps, DCP, UCP, LCP, fuel gas, oil systems, generator, excitation system, speed and vibration proximitors, thermocouples, RTD, heaters) as per Electrical a P&ID diagrams. Check remote wiring and interface (Control Room, customer Station Control System) -loop check, insulation, troubleshooting. Check calibrating protective devices Check and set motor starters. Test Electrical motor insulation resistance and polarization index (bump test, solo run, load test).

Project: Nord Stream 2, Pig Trap Area Russia (Baltic Sea Onshore). Conducting comprehensive test of electrical equipment (lighting system, electric motors, switchgear 0.4-10 kV, HVAC), emergency diesel generator, control of electrical measurements. Submission of proposals for the optimization of project solutions (power supply, fire automatics, SCADA, cathodic protection of the pipeline), participation/leadership in the commissioning work. Investigation of emergency events in the power supply system of the facility, fire alarm system, proposed and implemented technical solutions for the elimination of emergency events. Checking the compliance of the work documentation (E&I and Telecom, security system of the facility) with the requirements of regulatory documents, checking the implementation of author solutions on the site (Concession Request, Technical Query). Check and control of as-built documentation preparation, issuing comments. Contractors support in terms of work preparation, performance monitoring, reporting of progress.

Project: LLC Lukoil-Nizhnevolzhskneft. Development of oilfield V.I.Grayfer (first stage)». Offshore Ice-Resistant Fixed Platform. Check of conducting FAT fire extinguishing system compressor, expediting of the ventilation system and HVAC, FAT of HVAC, LV switchboards functional/acceptance check-out test, HV potential test. Project: Establishment of Integrated Cryogenic Engine (Space Propulsion) & Stage Test Facility (ICET), TATA Projects Ltd. India Factory Acceptance Test for ICET Control system PLC System (Prosoft-Systems Ltd. Base) included: Bill of Material and Hardware check, Equipment Check, I/O PLC inspection.

Control of the subcontractor (Design Institute and Construction subcontractros) to perform detailed design, in accordance with the project specifications and the requirements of the main contract; Monitoring the timing of design, coordination of changes and deviations from the project, coordinating the supply of materials with the project procurement department, working with equipment suppliers. Coordination of the work on electrical installation, fire alarm systems, instrumentation and automated control systems, commissioning, timely changes to the project in accordance with the executive schemes. Delivery of objects to the Customer, verification of as-built documentation.

Sakhalin-2, Onshore Processing Facility (LLC SGC) Fly camp construction. Process gas and condensate received from the Lunskaya-A platform for pipeline transportation to the oil export terminal and LNG plant. Control of the subcontractor (Design Institute) to perform detailed design, in accordance with the project specifications and the requirements of the main contract; Monitoring the timing of design, coordination of changes and deviations from the project, coordinating the supply of materials with the project procurement department, working with equipment suppliers. Coordination of the work on electrical installation, fire alarm systems, instrumentation and automated control systems, commissioning, timely changes to the project in accordance with the executive schemes. Delivery of objects to the Customer, verification of as-built documentation.

Check installation (checking QC forms status in the Easy Plant of Technip company) before pre-com/commissioning of electrical equipment: commissioning switchgear 0,4/10/35 kV (Gas Insulation Switch - Siemens, ABB, General Electric) – checking relay protection (Siprotec, Simocode), ATS/MTS (auto transfer scheme), PDCS –power distribution control system (Siemens); solo run/bump test for electrical motors; functional test activities for VSDS (Variable Speed Drive System –General Electric, ABB), Gas turbine (GE), Turbo compressors (GE), exciter (GE). Organizing commissioning activities at the site among subcontractors. Manage of activities of electricians at the substations.

Bureau Veritas, Abu-Dhabi (United Arab Emirates) Technical services and solution in the fields of certification, conformity, assessment, consulting and training. Work place: LUKOIL Kandym Development Project, Construction of Gas Processing Plant, Uzbekistan. Coordination and supervision of Construction support activities during the performance of the pre-commissioning, commissioning activities, High Potential Test for HV cables and HV equipment. Working in PTW (permit-to-work) system, checking the LOTO (Lock OUT/Tag OUT) during high potential test and equipment test; Installation and of electrical equipment: Pentair/Raychem control panels of electro heat tracing for piping, switchgear & package substation 10 kV; grounding and lightning systems, lighting system; laying cable ladders/trays and HV/LV cables; Issue daily reports for Customer Chief Expert about conducted High potential tests and Insulation Resistance tests; Installation of Instruments equipment: field instruments, gauges, transmitters, flowmeters (ultrasonic and differential pressure), instrument relay cabinets, junction boxes; mount of air tanks, manifolds, lock valves and instrument neumatic lines; installation grounding system for electrical and instrumentation, loop test; installation telecom system at the unit (data network, access control, laying fiber optic cable).

Work place: Indonesia, Batam Island, McDermott, yard assembly modules for the Yamal LNG plant. Coordination and supervision of Field Engineers and Technicians during the performance of the pre-commissioning, commissioning activities; Working in the PTW system and LOTO system during Supervising for high potential test for HV cable lines (cross-linked polyethylene), HV electrical equipment and Insulation Resistance for HV/LV cable lines (Prysmian, Draka with XLPE и PVC insulation); Using up activities EASYPLANT Software (technical design specification, project data Base xDB); Witnessing of tests, acceptance of hidden works, instrumentation and electrical systems as per design (technical design specification, project data Base xDB, Easy Plant) of the Client and normative documents (SNiP, PUE, GOST R, Federal Laws of RF, IEC, IEEE, NEMA, ASME); Technical solution has been implemented –introduced power cable routing change of the ventilation unit (HVAC) of the electro substations; Issued and cleared more than 75 NCR (Punch list) non conformity register upon Request for Inspection; Preparing dual language reports, conclusions of readiness for facilities after installation commissioning of modules for Yamal LNG. Provide effective troubleshooting during pre-commissioning and loop test; Participation in the tripartite meetings of the Customer-Contractor-Subcontractor on the formation of Module Fabrication Dossier; Fabrication of modules of electro substations of LNG compressors, technological modules for work in the hazard areas. Installation and pre-commissioning of electrical equipment: control panels the preservation heater panels (Chromalox), Variable Speed Drive System 10 kV(ABB), switchgear 10 kV (ABB); Pentair/Raychem electro heat tracing for piping, lighting, grounding and lightning systems. Installation and pre-com of the Process Control System and Instrumentation: field instruments, gauges, transmitters, any valves; Instrument relay cabinets; mount of air tanks, manifolds, calibration and testing field instruments at the Instrument shop (HART protocol) – transmitters and different purpose valves; installation telecom system at the modules (data network, telephony, PAGA, CCTV, access control), installation grounding system for instrumentation. Fire and Gas system: installation check of fire and gas detectors; capillary tubes, aspirating smoke detectors of High sensitivity Smoke Detectors (Xtralis Ltd. PTY), gas analysis instrument OPECL and PIRECL (Det-Tronics), smoke detectors (Apollo), Fire Alarm Control Panels (Yokogawa), Heat detector (Cooper MEDC Ltd.);

Incoming inspection supervision for materials, cable production and electrical equipment, equipment of cathodic protection Supervision Contractor as per design documents and regulations in the sphere of Construction supervision over Contractor activities, control over implementation of project decisions. - supervision for high potential test and megger test of electrical equipment. - reports two languages; - checkup of permits and as-built documentation of Contractor; - checkup of Method Statements on controllability; - acceptance of the facilities into operation, checkup of arrangement of documentation; Caspian Pipeline Consortium. Expansion. Tank Farm and Onshore facilities of CPC marine terminal, Novorossiysk. Pump stations on the territory of Krasnodar, Stavropol and Astrakhan regions and in Republic of Kalmykia. Participation in testing of HV electrical equipment and HV/LV cable lines with using PTW/LOTO systems; Installation electro substations range voltage 35/10/0.4 kV; Mount cable ladders, trays and laying Low Voltage and High Voltage Cables in the ground and over cable racks. Installation and of lighting system (indoor/outdoor), grounding and lightning systems, static electricity protection of tanks; Installation cathodic protection system for tanks and pipe sections at the Tank farm and Pump stations; Installation of diesel electro stations at the facilities; Khanti-Mansiysk Autonomous Region. 1.Correction of output for FTPS at the license area Kamennoe considering connection of PS-110/35/6 kV of Pump station № 32; 2. Oil processing area and reservoir pressure maintenance. Pump station № 24. Reconstruction VST-5000 of Tank farm. Electric installation, automatics for tanks, fire alarm automated; 3. Construction and reconstruction HV-6 kV at the deposits; 4. Technical upgrade of HV-35 kV «Knot-199 – PS-15» at Talinsk license area KNGM; at PS-35/6 kV PS-28, construction of HV-35KW;

Non-stop work of the automated systems and HVAC electric installations. Maintenance of controllers of Siemens, Segnetics Pixel, SI-34. Supervision over personnel on site.

- Organization of testing of electric equipment 0,4-110 kV during commissioning and maintenance (operation) process; - issuing permit-to-work, checking Lock Out/ Tag Out; - making diagnostics of different electric equipment (transformers, engines and etc.), issue of reports in due formats; - search for damages in the equipment; - carried out high-potential test for HV motors and HV switchgears; - qualification of test units, and metrological equipment of the Lab; - Work as an Acting Chief of Test Electric Laboratory; Engineer of Relay Protection and Emergency Automation - maintenance, commissioning, installation and repair of Relay Protection and Emergency Automation installations for process equipment (0,4-10 kV); - issuing permit-to-work, checking Lock Out/ Tag Out; - Arrangement of technical documentation for Relay Protection and Emergency Automation installations: passports, records, maintenance formats and charts for set up; - development of programs for technical decisions (9 decisions were introduced), Maintenance instructions for Relay Protection and Emergency Automation, installation charts, - Analyses for Relay Protection and Emergency Automation in the subdivision and work reports drawing up; - development of installation diagrams for Relay Protection and Emergency Automation in Autocad; - carried out of retro fitting for rolling devices (with circuit reinstalling Control Unit/TEL) from oil into vacuum ones Switchgear-10 kV feeding of equipment non-stop; - Acceptance of materials into operation, study of design documentation, control over start up works (microprocessor units Relay Protection BMRZ – start up, signal output for I&E and control systems) sections of Switchgear-10 kV basic production; - right away equipment fixing up (and mutual search for discrepancies in work of I&E equipment).

Senior operating specialist of installations of 0,4-110 kV; - Electric operation Engineer (V of electric safety) – issuing permit-to-work, checking Lock out/ Tag out system; - carried out high-potential test for HV motors and HV sweatchgears; - operating Turbogenerator 60 MW, 110 MW (with hydrogen cooling system) and auxiliary equipment; - Acting Head of maintenance shop (35 subordinate persons); - Acting regulatory requirements, protocols for Head of shifts; - developing safety instructions for work with electric installations (Permit-to-work system and Lock Out/Tag Out system), update diagrams, complex on-ling switching diagrams (110 kV); - Developing and carrying out of trainings for personnel; - organization of stable work for electric installations; - elimination of emergency situations on the plant; - Maintenance of electric installations of 0,4-110 kV, acceptance of repaired items, and maintenance of log-books.

- repair of units 0,4-6 kV capacity up to 1 MW, rigging work – foreman; - acting Engineer for equipment repair: support documentation preparing and accompanying of equipment on its way to plant, making up requests for equipment.

Engineering cybernetics, Electric feeding of Plants

Training centre, First aid training (Certificate)

PEIPK (St. Petersburg), St. Petersburg, "Testing, metering and diagnostics of EI up to 35 kV" (certificate)

Training centre, Autocad advanced users

Training centre, Training for slingers